Olympia Chimney Chimney Cap Installation Nationwide

Olympia Chimney Chimney Cap Installation: The Sandy Springs Owner’s Guide

We stock and install Olympia Chimney-compatible chimney caps for most residential flue sizes in Sandy Springs, with typical installed pricing running $280-$520 depending on cap style and whether your flue needs a mounting adapter. Most replacements are completed in under two hours, and we carry common Olympia Chimney cap sizes on every truck. The camera doesn’t guess. Neither do we.

Call (470) 480-0885

Most Sandy Springs homeowners discover their chimney cap has failed during a heavy rainstorm, when water starts hitting the firebox floor, or when they spot rust streaks running down the brick after our wet Georgia springs. Others notice the cap has blown crooked after one of the wind events that roll through the Abernathy Road corridor each March and October. A missing or damaged cap is an open invitation for water, animals, and debris to enter your flue, and in Sandy Springs’ humid subtropical climate, that moisture accelerates liner deterioration faster than in drier regions.

Which Olympia Chimney Models This Applies To

Olympia Chimney produces several cap lines, and the correct match depends on your flue type and existing top-sealing assembly. We most commonly see their stainless steel single-flue caps and multi-flue chase covers on homes built between 1985 and 2010 across Sandy Springs, particularly the ranch and split-level stock near Spalding Drive and the older brick colonials closer to the Chattahoochee.

To identify your cap, look for the Olympia Chimney stamp on the underside of the lid or the model number etched on the mesh screen frame. Single-flue caps typically fit flue tiles measuring 8×8, 8×13, or 13×13 inches, though we have measured “standard” flues in Sandy Springs that ran 7.75 inches true after decades of creosote buildup narrowed the opening. Multi-flue chase covers require exact length and width measurements of the chase top, plus the flue pipe center-to-center spacing. We bring a full sizing kit to every appointment.

OEM Olympia Chimney caps are available through Haven’s buying network, and we also source quality aftermarket equivalents from Gelco and Famco when the original line has been discontinued or when a homeowner wants a heavier-gauge upgrade. We will show you both options on the estimate, with the spec difference noted in writing, before you decide.

Signs Your Olympia Chimney Chimney Cap Installation Is Failing

• Rust stains on the chimney breast or fireplace surround. Olympia Chimney caps use 304 or 316 stainless steel, but the spot-welded corners and mesh screen frames are the first failure points in Sandy Springs’ acid-rain pattern. Once rust breaches the surface, the cap is shedding metal particles into your flue and losing structural integrity.
• Water in the firebox after rain. This usually means the cap lid has separated from its base, the mesh has torn away, or the storm collar has cracked. In homes near the Chattahoochee River basin, we see accelerated UV degradation on the rubber storm collars after about seven years of Georgia sun exposure.
• Mesh screen pulled loose or missing entirely. Squirrels and raccoons can force entry through weakened mesh, especially on caps where the spot welds have corroded. Corrine has logged seven bird species and counting in Sandy Springs chimneys, and every one entered through a cap that looked fine from the ground.
• Cap sitting crooked or blown off entirely. The spring steel tension legs on older Olympia Chimney single-flue caps fatigue after repeated thermal cycling. Once the grip loosens, a 40 mph gust, common in spring frontal systems here, can rotate or lift the cap.
• Spalling brick or deteriorating mortar at the chimney top. This is downstream damage from a cap that has been leaking for seasons. Water freezes in the masonry pores during Sandy Springs’ intermittent winter cold snaps, expanding and flaking the brick face. The cap failure caused this, and replacing the cap without addressing the masonry just guarantees repeat damage.

Before

After

Replacement Cost & What’s Included

The range reflects cap material gauge (24-gauge standard vs. 20-gauge heavy-duty), whether your flue requires a custom adapter, and accessibility. Two-story chimneys with steep pitches near the Sandy Springs border with Buckhead take longer to rig safely than single-story ranch caps. Every quote is written before work starts, with the scope, the exact cap spec, and the 365-Day Done Right Promise noted. Haven Standard Clause 1 requires it. We do not start work on a verbal number.

Your documented photo record, including the cap fit and the flue condition beneath it, is archived under Haven Standard Clause 4 and provided before we leave. Materials are sourced through Haven’s buying network from Olympia Chimney, Gelco, Famco, and Copperfield to keep pricing honest.

DIY or Call Us?

You can safely check whether your cap is loose by sighting up from the firebox with a flashlight, or by examining the cap from ground level with binoculars. Do not climb the roof to tug on it. Chimney caps sit at the highest point of your home, often on a slope, and the metal edges are sharp enough to open a palm if the cap shifts unexpectedly.

Installation requires proper fall protection, knowledge of flue tile fragility (a cracked tile from overtightened legs becomes a $1,200 liner conversation), and verification that the new cap does not obstruct draft. We have replaced three caps this year in Sandy Springs where the homeowner’s self-install seated the cap too low, trapping combustion gases. The camera found it. The camera doesn’t guess. Neither do we.

Call (470) 480-0885 for a written estimate. Estimates are free, and we will show you the exact cap and the camera footage before quoting a number.

FAQs