Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Sandy Springs: What to Know First

We provide independent Olympia Chimney chimney cap & crown service in Sandy Springs, from cap replacement on a rusted 304SS model to crown coating on a poured-concrete stack that’s taken sixteen years of Georgia ice cycling. Most Olympia Chimney cap and crown jobs we book run one to three hours on site, and every one starts with a written price before we touch a tool. If you’re seeing water stains on your firebox ceiling, hearing metal flapping in a March windstorm, or finding brick flakes in your yard after a freeze, you’re who this page is for. Call us at (470) 480-0885 for a free estimate with no obligation to book.

Call (470) 480-0885

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia 304SS single-flue caps: The 18-gauge 304 stainless holds up well in Sandy Springs’ acid-rain pattern, but the spot-welded corner seams crack at year 8-12 when pine needle debris traps moisture against the weld heat-affected zone. We see this on homes near the Chattahoochee River corridor where loblolly pine is dense. We replace with a heavier 20-gauge cap or switch to a Gelco multi-flue with fully seam-welded construction, depending on flue count and your budget.
• Olympia galvanized steel economy caps: These show red rust bloom at the drip edge within four to six years in Sandy Springs’ humidity, faster if the cap sits below tree line where leaves hold dew. The rust isn’t cosmetic; it stains the crown and accelerates spalling in the concrete below. We pull the galvanized cap, inspect the crown substrate for saturation damage, and upgrade to stainless or copper if the homeowner plans to stay in the house.
• Olympia multi-flue caps with mesh sides: The 5/8-inch mesh on Olympia’s multi-flue units clogs with cottonwood seed in late May and June, especially in the older neighborhoods off Roswell Road where mature trees overhang roofs. The restricted airflow cools flue gases, accelerating creosote buildup. We clean the mesh in place if the cap frame is sound, or replace with a Famco model using 3/4-inch mesh and a steeper lid pitch that sheds debris.
• Olympia chimney crowns (poured concrete): Olympia’s crown mix is specified at 4,000 PSI, which is adequate, but the pour is often thin at the flue overhang where the concrete feather-edges. In Sandy Springs, that thin edge is the first place freeze-thaw pops it. We find this on ranch-style homes near Abernathy Road built in the 1970s and 1980s. Our fix is crown coating with HeatShield CrownCoat after grinding back the damaged edge, or a full pour if the steel reinforcement is exposed.
• Olympia cap-to-crown seal: The caulk joint between cap base and crown concrete fails in three to five years, not from the caulk quality but from the differential movement between the metal cap and concrete crown in summer heat. Water runs behind the cap flange and rots the top course of brick. We remove the old sealant, prime the concrete, and bed the cap in a polyurethane sealant with 35% joint movement capability, not the cheap silicone the original installer used.

Our Olympia Chimney Chimney Cap & Crown Process

1. 1
   Call and schedule: A live person answers, checks availability in Sandy Springs, and notes your Olympia Chimney model if you know it. We don’t require the model; we identify it on site.
2. 2
   NFPA 211 Level 2 inspection: Corrine Halstead or a uniformed, background-checked technician arrives with a camera rig. We run the camera down the flue before quoting any cap or crown work. The camera doesn’t guess. Neither do we.
3. 3
   Written scope and price: You get a single-page document: what we found, what we’ll do, what parts we’ll use (OEM Olympia Chimney or quality aftermarket from our Haven buying network), and the exact price. No work starts until you sign it. Haven Standard Clause 1.
4. 4
   Cap or crown work: We fabricate or source the replacement cap, grind and prep the crown, apply coating or pour new concrete, and reinstall with proper sealant and counterflashing.
5. 5
   Post-work camera verification: We run the camera again to confirm no debris fell into the flue during the repair, and we photograph the completed cap and crown from the roof. Haven Standard Clause 4 requires the photo record; you get it by email before we leave.
6. 6
   Cleanup and documentation: We haul old materials, sweep the work area, and leave you with the written warranty and our 365-Day Done Right Promise stamped on the invoice.

Before

After

What Olympia Chimney Chimney Cap & Crown Costs in Sandy Springs

These are Sandy Springs prices for 2024-2025, reflecting what we pay through our Haven buying network for Olympia Chimney, Gelco, Famco, and DuraFlex materials. Every estimate is free and fixed in writing before work begins. Call (470) 480-0885 for your exact number.

Why Sandy Springs Homeowners Call Emberly Chimney Cleaners Sandy Springs for Olympia Chimney Work

We’ve inspected and cleaned more than 38,000 chimneys since 2009, and a running subset of those are Olympia Chimney caps and crowns in Sandy Springs homes. Corrine Halstead runs crews here personally; she knows the older ranch stock near Abernathy Road where the flues practically introduce themselves, and she knows which Olympia Chimney models were spec’d on the 2015-2020 build wave off Hammond Drive. Our technicians are background-checked, uniformed, and named on your appointment text, license number included. We also service DuraFlex, HeatShield, and Gelco systems, so if your Olympia Chimney component is discontinued or a different brand makes more sense for your flue configuration, we’ll say so and show you the comparison in writing. The 365-Day Done Right Promise applies to every job. If it’s not right, we make it right.

FAQs